This is in prep toward doing fsp graphics updates from the main quotes
update loop (where OHLC and volume are done). Updating fsp output from
that task should, for the majority of cases, be fine presuming the
processing is derived from the quote stream as a source. Further,
calling an update function on each fsp subplot/overlay is of course
faster then a full task switch - which is how it currently works with
a separate stream for every fsp output. This also will let us delay
adding full `Feed` support around fsp streams for the moment while still
getting quote throttling dictated by the quote stream.
Going forward, We can still support a separate task/fsp stream for
updates as needed (ex. some kind of fast external data source that isn't
synced with price data) but it should be enabled as needed required by
the user.
The major change is moving the fsp "daemon" (more like wanna-be fspd)
endpoint to use the newer `tractor.Portal.open_context()` and
bi-directional streaming api.
There's a few other things in here too:
- make a helper for allocating single colume fsp shm arrays
- rename some some fsp related functions to be more explicit on their
purposes
A `QRectF` is easier to make and draw (i think?) so use that and fill it
on volume events for decent sleek real-time look. Adjust the step array
generator to allow for an endpoints flag. Comment and/or clean out all
the old path filling calls that gave us perf issues..
Turns out the performance of updating and refilling step curves > 1k ish
points is super slow :sadkek:. Disabling the fill basically returns
normal performance, so it seems maybe we'll stick with unfilled volume
"bars" for now. The other tricky bit is getting the path to extend and
fill which is particularly slow if you use the `QPainterPath.united()`
(what `+` set op does) operation which seems to require an entire redraw
of the curve each paint iteration. Removing the pixel buffer cache makes
things that much worse too..
One technique i tried was only setting a `._fill` flag when so many
datums are in view (< 1k as determined by the chart widget), and this
helps, but under high load (trade rates) you still see more lag then
without the fill which makes me say screw it and let's stick with
unfilled bars for now. Trying go to get performant filled curves will be
an exercise for an aspiring graphics eng :P
Toss in support for a "step mode" curve (unfinished atm) and use it to
plot from the `volume` field of the ohlcv shm array (if available).
changes to make it happen,
- dynamically generate the fsp sidepane form from an input config `dict`
|_ dynamically generate the underlying `pydantic` model
|_
- add a "volume checker" helper func that inspects the shm array
- toss in sidepane resize calls to avoid race where the ohlcv array
is plotted too slowly compared to the volume and the chart somehow
doesn't show..
- drop duplicate rsi2 cruft (previously used to test plots of the shm
data)
In latest `pyqtgraph` it seems there's a discrepancy
since `function.arrayToQPath()` was reworked and now
we need to *not* connect the last point for each bar.
This should finally be correct fsp src-to-dst array syncing now..
There's a few edge cases but mostly we need to be sure we sync both
back-filled history diffs and avoid current step lag/leads. Use
a polling routine and the more stringent task re-spawn system to get
this right.
There was a lingering issue where the fsp daemon would sync its shm
array with the source data and we'd set the start/end indices to the
same value. Under some races a reader would then read an empty `.array`
which it wasn't expecting. This fixes that as well as tidies up the
`ShmArray.push()` logic and adds a temporary check in `.array` for zero
length if the array hasn't been written yet.
We can now start removing read array length checks in consumer code
and hopefully no more races will show up.
Litter the engine code with `pyqtgraph` profiling to see if we can
improve startup times - likely it'll mean pre-allocating a small fsp
daemon cluster at startup.
Tyler Goodlet
goodboy